Enhanced mechanical properties of glass fibre epoxy composites by 2D exfoliated graphene oxide filler

Graphene oxide (GO) received a significant attention in the scientific community due to their excellent mechanical properties identifying themselves as an alternative and combinatory to various other metals and composites. Though GO possess excellent strength, it was observed from the literature that graphene oxide consisting of hydroxyl group elements ensue in poor bonding. Thus reduced functional group density (rFGD) graphene is preferred which has an advantage of good bonding, alongside very small quantity as a filler is required to achieve the enhancement equivalent to graphene oxide which forms the novelty of the current work. In current case, 3, 6 and 9 wt% of rFGD is dispersed into E-glass fibre reinforced composite by traditional hand layup technique. The obtained results revealed that, the tensile, flexural and impact strength have shown superior enhancement with 3 and 6 wt% of rGO than neat E-glass epoxy (0 wt% rGO), whereas an asymptotic decrement is noticed at 9 wt% when tested with ASTM standards except for impact strength. The microstructural studies also indicated the proper adhesion and alignment of fibres without any agglomerations corroborate the enhancement of properties. These overall finding supports the suitability of the developed laminates for potential use in structural applications in aerospace industry.     

Effect of laser power density on the electrochromic properties of WO3 films obtained by pulsed laser deposition

Pulsed laser deposition (PLD) was used to prepare tungsten trioxide (WO₃) films on ITO substrates with a varying laser power density of 4.0–5.5 W/cm². XPS indicated that when the laser power density decreased, the peak positions of the W 4f and O 1s orbits shifted slightly to low energy due to the difference in oxygen vacancies. As the laser power density decreased, W⁶⁺ gradually replaced the lattice position of O^2?, increasing oxygen vacancies in the lattice. The transmittance modulated values (ΔT) were over 44% at 830 nm, indicating strong absorption by the WO₃ thin films in the near-infrared ray. The switching time of the WO₃ thin films between bleached states and coloured states decreased as the laser power density increased due to the amorphous structure, morphology, and lower oxygen deficiency at a high power density. The high ΔT and very fast switching time of t_b (1.09 s) and t_c (6.01 s) demonstrated the excellent electrochromic (EC) properties of the WO₃ films prepared by PLD.     

Bioceramic composites for orthopaedic applications: A comprehensive review of mechanical,biological, and microstructural properties

Bioceramics have been widely utilized for orthopaedic applications in which the biocompatibility and mechanical properties of the materials are vital characteristics to be considered for their clinical use. Till date, extensive studies have been devoted to developing a range of scientific ways for tailoring the microstructure of bioceramics in order to attain the trade-off of mechanical properties and biocompatibility of the final product. Owing to low reactivity, earlier stabilization and longer functional life of bioceramic, the developed implants are capable of replicating the mechanical behaviour of original bone. As the safety of the patient and its ultimate functionality are the ultimate goal of the selected implant material hence, the present literature survey investigates and brings forth the important aspects associated to the mechanical, biological and microstructural characteristics of bioceramics employed in orthopaedic applications. The review paper majorly focuses on effective utilization of various materials as an additive in bioceramics and processing techniques used for enhancement of properties, enabling the use of material in orthopaedic applications. The influence of various additives on the microstructure, mechanical properties and biological performance of developed bioceramics orthopaedic implants has been elaborately discussed. Furthermore, future prospects are proposed to promote further innovations in bioceramics research.     

Effect of lattice structure evolution and stacking fault energy on the properties of Cu–ZrO2/GNP nanocomposites

A hybrid nanocomposite comprising nanosized ZrO₂ and graphene nanoplatelet (GNP)-reinforced Cu matrix was synthesised via powder metallurgy. The influence of sintering temperature and GNP content on the electrical and mechanical behaviour of the Cu–ZrO₂/GNP nanocomposite was investigated. The ZrO₂ concentration was fixed at 10% for all the composites. Upon increasing the GNP concentration up to 0.5%, a significant improvement was observed in the compressive strength, microhardness, and electrical conductivity of the composite. Furthermore, the properties were significantly improved by increasing the sintering temperature from 900 to 1000 °C. The compressive strength, hardness, and electrical conductivity of Cu–10%ZrO₂/0.5%GNP were higher than those of the Cu–ZrO₂ nanocomposite by 60, 21, and 23.8%, respectively. This improvement in the mechanical properties is because of the decrease in the crystallite size and dislocation spacing, which increases the dislocation density, thereby increasing the impedance towards dislocation movement. The lower stacking fault energy of the hybrid nanocomposites enables easier electron transfer within and between the Cu grains, resulting in an improved electrical conductivity. The enhancement in strength and electrical conductivity were aided by the GNPs and ZrO₂ nanoparticles that were dispersed widely in the Cu matrix.     

Mechanical and dielectric properties of functionalized boron nitride nanosheets/silicon nitride composites

Uniformly dispersed boron nitride nanosheets (BNNSs) reinforced silicon nitride (Si₃N₄) composites were prepared by surface modification assisted flocculation combined with SPS sintering. In order to improve the dispersibility of the BNNSs in the composites, the liquid phase stripped BNNSs are surface functionalized by a two-step covalently modification. The amino-modified BNNSs (NH₂-BNNSs) and Si₃N₄ powders have opposite surface potential, mixed evenly by electrostatic interaction during flocculation. The results showed that mechanical properties of Si₃N₄ composites were obviously enhanced by adding NH₂-BNNSs. The fracture toughness and bending strength of Si₃N₄ composites added 0.75 wt% NH₂-BNNSs were increased by 34% and 28%, respectively, compared with monolithic Si₃N₄. Toughening mechanisms are synergistic action of the torn, pull-out or bridging of BNNSs and crack deflection mechanisms with microstructural analyzes. The dielectric properties of the Si₃N₄ ceramics are also improved after the addition of NH₂-BNNSs.     

Optical properties of gadolinia-doped cubic yttria stabilized zirconia single crystals

Cubic zirconia single crystals stabilized with yttria and doped with Gd₂O₃ (0.10–5.00 mol%) were prepared by the optical floating zone method, and characterized by a combination of X-ray diffraction (XRD), and Raman, electron paramagnetic resonance (EPR), ultraviolet–visible (UV–Vis), photoluminescence excitation (PLE) and photoluminescence (PL) spectroscopic techniques. XRD and Raman spectroscopy showed that the crystal samples were all in the cubic phase, whereas the ceramic sample consisted of a mixture of monoclinic and cubic phases. The absorption spectrum showed four peaks at 245, 273, 308, and 314 nm in the ultraviolet region, and the optical band gap differed between samples with ≤3.00 mol% and those with >3.00 mol% Gd₂O₃. The emission spectrum showed a weak peak at 308 nm and a strong peak at 314 nm, which are attributed to the ⁶P_5/2 → ⁸S_7/2 and ⁶P_7/2 → ⁸S_7/2 transitions of Gd³⁺, respectively. The intensities of the peaks in the excitation and emission spectra increased with Gd³⁺ concentration, reached a maximum at 2.00 mol%, then decreased with higher concentrations. This quenching is considered to be the result of the electric dipole-dipole interactions, and this interpretation is supported by the Gd³⁺ EPR spectra, which showed progressive broadening with increasing Gd³⁺ concentration throughout the concentration range investigated.     

Impact of the Zr-substitution on phase composition,structure, magnetic,and microwave properties of the BaM hexaferrite

Rapid developments in information technologies and a large rise in electrical and electronic equipment have generated different forms of electronic environmental contamination. Microwave absorption materials are important to avoid the damage that can be caused by electromagnetic radiation. A necessary condition for the absorption of the most incoming radiation is balanced wave impedance at the air/shield interface, which depends on the studied materials' magnetic and electrical properties. The paper introduces the preparation of BaFe_12-xZr_xO₁₉ (x = 0.1, 0.3, 0.6, 0.9, and 1.2) using a solid-state reaction technique. The studied samples were examined by X-ray diffraction, scanning electron microscopy, vibrating sample magnetometer, and a vector network analyzer. The studied samples showed that controlling the grain size and the prepared samples' magnetic properties play an important role in enhancing the microwave radiation absorption. The examined samples can be a promising absorption material in electromagnetic shielding applications.     

Thermoset IM-LSI-based C/C-SiC: Influence of flow direction and weld lines on microstructure and mechanical properties

The production of ceramic matrix composites (CMC) based on C/C-SiC is still very cost-intensive and therefore only economical for a few applications. The fabrication of the preforms involves many costs that need to be reduced. In this work, the shaping of the CFRP-preforms is realized by thermoset injection molding, which enables large-scale production. The polymeric matrix used is a multi-component matrix consisting of novolak resin, curing agent and lubricant. Six millimeter chopped carbon fiber with a proportion of 50 wt.% were used as a reinforcement. These ingredients are processed by an industrial equipment for compounding and injection molding in order to manufacture a CFRP demonstrator representing a brake disc. Test specimens are cut out of the demonstrator in different directions in order to investigate influences of flow direction and weld lines on microstructural and mechanical properties. Afterward, the CFRP samples were converted to C/C-SiC composites by the liquid silicon infiltration process. The article addresses the flow behavior of the compound during the injection molding and the building of the weld lines in the demonstrator. In addition, results of the directional dependence of the microstructural and mechanical properties within the fabricated disc in the different production steps are presented.     

Cyclic thermal shock resistance of h-BN composite ceramics with La2O3–Al2O3–SiO2 addition

The effects of La₂O₃–Al₂O₃–SiO₂ addition on the thermal conductivity, coefficient of thermal expansion (CTE), Young's modulus and cyclic thermal shock resistance of hot-pressed h-BN composite ceramics were investigated. The samples were heated to 1000 °C and then quenched to room temperature with 1–50 cycles, and the residual flexural strength was used to evaluate cyclic thermal shock resistance. h-BN composite ceramics containing 10 vol% La₂O₃–Al₂O₃ and 20 vol% SiO₂ addition exhibited the highest flexural strength, thermal conductivity and relatively low CTE, which were beneficial to the excellent thermal shock resistance. In addition, the viscous amorphous phase of ternary La₂O₃–Al₂O₃–SiO₂ system could accommodate and relax thermal stress contributing to the high thermal shock resistance. Therefore, the residual flexural strength still maintained the value of 234.3 MPa (86.9% of initial strength) after 50 cycles of thermal shock.